产品描述
SH-620 有机硅离型剂
一、性能及用途
本产品属加成型无溶剂型有机硅离型剂。轻离型力，加热快速固化，萃取率低，具有稳定的剥离力、优良的对基材附着力和浴槽稳定性。本产品主要用于要求轻剥离力的淋膜纸和格拉辛纸涂硅。用于淋膜纸时主要集中在牛皮淋膜纸方面，终端应用集中在墙纸、鞋材等产品。用于格拉辛纸时终端应用集中在快速自动贴标等应用。
二、主要技术指标
|
项目 |
指标 |
|
外观 |
无色透明液体 |
|
粘度（25℃）/cp |
300-500 |
|
活性成分/% |
100 |
|
测试基材 |
PE淋膜纸 |
|
干硅量/(g/m2) |
1 |
|
速测离型力（20min）/(gf/25mm) |
3-5 |
|
老化离型力（70℃,24h）/(gf/25mm) |
5-8 |
|
残余黏着率（70℃,24h）/% |
≥90 |
三、使用参考
推荐采用以下步骤配制涂布液。设备应洁净。首先加入主剂。再加入交联剂，搅拌均匀。最后慢慢加入催化剂，搅拌均匀。通常情况下，涂布液寿命为6小时。
将过滤后的涂布液均匀涂覆在基材上，在烘箱中加热固化。可参考实验室固化测试时的温度和时间：140℃*20s。
使用注意事项：
1.此产品易受过氧化物和其它物质的污染，如含有机锡的物质、含硫的物质、氨基化合物等。请清洁所有混合设备和涂敷设备，并尽可能使用专用的容器。
2.为了更好地使用本产品，务必调整使用工艺使产品尽可能固化完全。
四、包装及贮运
常规包装20kg/桶，200kg/桶；可根据用户需求协商指定包装。请储存于阴凉、干燥、通风处，牢固密封保存。自生产日期起，本产品在30℃以下的保质期为12个月。
SH-620 Silicone Release Coating
Ⅰ. Product Description
SH-620 is an addition-curing and solvent-free Silicone Release Coating. It features light release force, rapid thermal curing and low extraction rate. It also offers stable peel force, good adhesion to substrates, and excellent bath stability. It is mainly used for silicone coating on coated paper and glassine paper that requires light release force. For coated paper, it focuses on kraft release paper with end products such as wallpaper and shoe materials. For glassine paper, end products are primarily high-speed automatic labeling.
Ⅱ. Technical Data
|
Item |
Index |
|
Appearance |
Colorless transparent liquid |
|
Viscosity (25℃, cp) |
300~500 |
|
Active Ingredient Content (%) |
100 |
|
Test Substrate |
PE-coated paper |
|
Silicone Coat Weight (g/m2) |
1 |
|
Rapid Release Force (20min, gf/25mm) |
3~5 |
|
Aged Release Force (70℃,24h, gf/25mm) |
5~8 |
|
Subsequent Adhesion Strength (70℃, 24h, %) |
≥90 |
III. How to Use
Prepare the coating solution as described later. Keep the equipment clean. Firstly, add base component. Then add cross-linking agent and stir evenly. Finally, add catalyst slowly and stir evenly. The typical pot life of the coating solution is 6 hours.
Apply the filtered coating solution evenly onto the substrate, and then cure it in the oven, like under laboratory conditions, 20 seconds at 140℃.
Note:
- This product is easily contaminated by peroxides, amino compounds, other substances that contains, for example, organotin or sulfur. Therefore, please clean all the mixing and coating equipment and use an exclusive container whenever possible.
- For better use, please adjust the process to make sure the product is cured as fully as possible.
Ⅳ. Packaging and Storage
It is sealed in standard packaging as in 20kg/ drum, 200kg/ drum, or customized as per customer request. Please store it in a cool, dry and well-ventilated place in unopened packaging. The shelf life is 12 months below 30℃.
上一页
上一页
下一页
在线咨询